Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 185 / 296

Move the rubber joint (M mark) of the

rubber track shoe to the upper center

between the axles.

Swing the machine 90 degrees, place the

bucket on the ground, and retract the boom

cylinder to raise the track shoe to be

checked. Then support the lower frame with

safety strut (1).

At the center of the crawler frame, measure

gap (A) between the lower surface of the

crawler frame and the upper surface of

the track shoe.

1. Crawler Frame/2. Lower Roller

3. Rubber Track Shoe/4. Iron Track Shoe

Proper tension "A" mm (inch):

Rubber: 70 to 80 mm (2.8 to 7.87 cm)

Iron: 120 to 135 mm (4.7 to 5.3 inch)

If the tension is not proper, see the next

section to adjust it.

４

Rubber Track Shoe/Iron Track Shoe

Working with loosen track shoes causes coming off or early wear of them.

Adjustment

It is necessary to adjust the track shoe tension depending on the work condition at the working site.

At the working site covered with many gravels and cobbles, loosen the track shoe tension as much as

possible within the proper range. On the firm ground, increase the tension slightly within the proper

range.

Grease nipple (1) can pop out due to the inner high pressure grease. Do not loosen it more than 1

turn.

The high pressure grease is charged in the grease cylinder of the track spring. When adjusting the

shoe tension or disassembling the shoe for maintenance, loosen grease nipple (1) within one turn to

discharge the grease gradually.

Keep the face and body away from grease nipple (1) when loosening it.

［

4. INSPECTION AND MAINTENANCE

］

4-43

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды