Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 208 / 296

Park the machine in the hydraulic oil

inspection position on the level and firm

ground, and then stop the engine.

Move the pilot control shut-off lever to the

"LOCKED" position.

Clean the surface around the hydraulic oil

tank to keep away from foreign materials.

Press breather cap (1) on the top of the

hydraulic oil tank several times (5 - 7

times) to release the internal pressure of

the hydraulic oil tank.

Remove bolt (2) of the tank upper cover,

and remove cover (3).

Check the drained oil, and if metal chips or powder is found in the oil, contact KOBELCO authorized

dealer/distributor.

Dispose of the drained waste oil properly as the industrial waste.

4.18.2

CLEANING SUCTION STRAINER

HANDLING OF HYDRAULIC OIL TANK

The oil in the hydraulic oil tank is under high pressure and high temperature.

Stop the engine first, remove the breather cap, press the valve, release the pressure from the tank,

and then remove the cover.

Immediately after operation, the oil is hot and it may cause burns. Wait until the oil temperature

cools down before attempting to change the hydraulic oil.

Hydraulic Oil Inspection Position

Do not drop bolts or others into the tank during the work.

［

4. INSPECTION AND MAINTENANCE

］

4-66

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды