Kobelco SK35SR-6 Скачать руководство пользователя страница 206

Страница: 206 / 296

4.17

1500 HOUR INSPECTION & MAINTENANCE PROCEDURES

Thoroughly read and understand "1. SAFETY PRECAUTIONS" of this manual before performing the

inspection and maintenance.

Follow this section together with daily, 50-hour, 250-hour, 500-hour and 1000-hour inspection and

maintenance.

4.17.1

INSPECTING AND ADJUSTING ENGINE

Checking, Adjusting and Cleaning Fuel Injection Valves

If the exhaust color is not good during operation and the engine output is lower than before, it may be

caused by bad injection condition of the fuel injection valves.

Optimize the fluid injection condition and tune the engine for the best performance.

Checking and Adjusting Fuel Injection Timing

Adjust the fuel injection timing to achieve the best engine performance.

Cleaning EGR Cooler

On the cooling water chamber side of the EGR cooler, rust and water scale are adhered after a

long-time use, which may deteriorate the cooling of EGR gas. On the exhaust passage side, too,

carbon is adhered, becoming a resistance to exhaust gas circulation and deteriorating the exhaust

emission value. Clean this part at least every 1500 hours.

Checking Crankcase Breather System

The crankcase breather system must work properly in order to ensure that the engine complies with

the emission regulation throughout its useful life.

Contact KOBELCO or KOBELCO authorized dealer/distributor for inspection and adjustment of the

engine.

［

4. INSPECTION AND MAINTENANCE

］

4-64

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды