Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 224 / 296

5.2

LOADING/UNLOADING THE MACHINE

5.2.1

LOADING WITH RAMPS

Perform a low speed travel to load/unload the machine.

Do not use the attachment for loading and unloading the machine to avoid danger.

Use only the travel levers when the machine is on ramps.

Be careful when going over the ramp top to/from a trailer because the machine center of gravity

changes abruptly.

Loading and unloading with attachment

Loading and unloading with ramps

Load/unload the machine on the level ground as much as possible.

Use a ramp with sufficient length, width, strength and gradient. Angle (A) of the ramps to the

ground should be 15 degrees or less.

Apply non-slip to the slippery surface on the ramps due to rain.

Make sure the machine position is aligned to the ramp before going up on the ramp, and travel

slowly. Raise the dozer, and load/unload the machine onto/from the trailer with the attachment

lowered as much as possible but not hitting the trailer.

When loading the machine with the attachment, going up to the trailer from the front of machine,

and when loading the machine without the attachment, going up to the trailer from the back of

machine.

Load the machine properly on the required position of the trailer.

Follow the procedures below to prevent damage to the arm and bucket cylinders.

Do not fully extend the arm and bucket cylinder when the center of the machine is going over the

ramp top to/from the trailer. If the cylinder is extended, the machine may abruptly lean to one side

(when it goes over the ramp top) and strike its arm or bucket cylinder against the trailer bed, ramp,

or ground, resulting in damage to the cylinder.

［

5. TRANSPORTATION

］

5-4

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды