Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 115 / 296

The control pattern of this machine can easily

be switched between two types by the lever of

the rotary multi-control valve.

Place the machine in the parking position,

stop the engine, and move the pilot

control shut-off lever to the "LOCKED"

position.

Open the cover at the front of the

machine to access rotary multi-control valve

(1).

Remove wing bolt (2), and switch lever (3)

to the position of the desired control pattern.

Tighten wing bolt (2) to fix lever (3) after

setting the control pattern. Firmly tighten

wing bolt (2) by your fingers without tools.

Close the cover.

Operate the attachment to make sure that

the desired control pattern is used.

３

3.8

ROTARY MULTI-CONTROL VALVE (ISO/BHL)

Before switching the rotary multi-control valve, lower the bucket to the ground, place the pilot control

shut-off lever in the "LOCKED" position, and stop the engine.

3.8.1

HOW TO SWITCH CONTROL PATTERNS

［

3. MACHINE OPERATION

］

3-21

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды