Kobelco SK35SR-6 Скачать руководство пользователя страница 44

Страница: 44 / 296

Never apply swinging force to a rock slide or

breaking work. It would exert excessive force

to the machine structure and

equipment/attachment, and could cause severe

damage to them to shorten the service life of

the swing system.

Never apply travel force to digging with the

bucket being wedged into the ground. It would

exert excessive force to machine parts and

could cause severe damage to them.

Never apply travel force to leveling the ground.

It could result in damage to the machine.

Never use the bucket for hammering and

piling. It may cause severe damage to machine

parts.

Operate the bucket, boom and arm cylinders

to leave some clearance (as clearance A in

the figure) to the both stroke ends.

If the cylinder is operated to the stroke end, it

will generate an excessive load and cause

damage to not only the cylinder but also the

pin, boom and arm.

1.6

PROHIBITED WORKS

1.6.1

PROHIBITED WORKS IN MACHINE OPERATION

DO NOT APPLY SWINGING FORCE TO THE FOLLOWING OPERATIONS

DO NOT APPLY TRAVEL FORCE TO DIGGING OR LEVELING

DO NOT PERFORM "HAMMERING" OPERATIONS WITH THE BUCKET

DO NOT OPERATE THE CYLINDERS TO THE STROKE END

［

1. SAFETY PRECAUTIONS

］

1-26

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды