Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 126 / 296

For more efficient loading work, place the

dump truck where the operator can easily

view it and the swing angle is smaller.

It is easier to load more soil onto the

dump truck from the front side of the back

than from the side.

To improve the efficiency, attach a bucket

suitable for trenching and place the crawlers

parallel to the trench to dig. When digging a

wide trench, dig both sides of it first and dig

the center last.

For backfilling and leveling work after

digging, use the dozer.

Scrape the embankment from the top or

side surface. If the load on the machine is

too much, adjust the dozer height by

using the dozer control lever to move the

dozer up and down.

In addition, you can use the machine for a wider range of purposes by using various optional

attachments.

For replacement of the bucket, see "WHEN REQUIRED" in Chapter 4.

3.10.2

LOADING WORK

3.10.3

TRENCHING WORK

3.10.4

DOZING WORK

［

3. MACHINE OPERATION

］

3-32

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды