Kobelco SK35SR-6 Скачать руководство пользователя

Страница: 63 / 296

・

Do not disassemble it.

・

Do not bring a fire near it, or throw it into

a fire.

・

Do not perform drilling, welding, or gas

cutting on it.

・

Do not shock it by striking or rolling it.

・

The charged gas must be removed before

disposal. Contact KOBELCO authorized

dealer/distributor.

１

1.11

HANDLING ACCUMULATOR

Improper handling of the accumulator containing high pressure nitrogen gas may cause severe injury

due to explosion. Follow the instructions below without fail when handling it.

For more information about handling the accumulator, contact KOBELCO authorized dealer/distributor.

［

1. SAFETY PRECAUTIONS

］

1-45

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды