Kobelco SK35SR-6 Скачать руководство пользователя страница 227

Страница: 227 / 296

５

5.4

MACHINE LIFTING PROCEDURES

Persons who work for lifting and slinging using a crane should have the following appropriate licenses.

･

Mobile crane operator's license

･

Certificate of skill training course for slinging operation

MACHINE LIFTING

･

A wire rope or other lifting tool used should have no damage nor deterioration, with sufficient

strength.

･

With improper method of lifting and placing wire ropes, the lifted machine may move, causing

personal injury or damage to the machine.

･

Be careful not to apply a load suddenly to the wire ropes and tools for lifting.

･

When lifting the machine as a group work, surely send and receive signals to each other.

･

Do not lift the machine with a worker on it.

･

During the machine lifting operation, keep away from the area around and under the machine.

･

Keep the machine horizontal when lifting it.

This lifting procedures are applicable for machines in a standard specification.

The lifting procedures differ for each attachment type and machine with an option specification. In such

cases, contact KOBELCO authorized dealer/distributor.

Operate the control levers to set the attachment in the position as shown in the figure.

If the boom is swung, operate the boom swing pedal to straighten it.

Stop the engine, check that nothing is left around the operator's seat, set the pilot control shut-off

lever to the "LOCKED" position, and then get off the machine.

Attach shackles to two lifting holes (A) on both ends of the dozer and place the wire rope on

them.

Attach a shackle to part (B) on the boom and place the wire rope on it.

［

5. TRANSPORTATION

］

5-7

Содержание SK35SR-6

































































































































































































































































Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды

Kobelco SK35SR-6, Руководство по эксплуатации

Результаты поиска

Содержание SK35SR-6

Отзывы:

Похожие инструкции для SK35SR-6

Бренды по названию

Популярные бренды