Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 100

Страница: 100 / 120

• Internal PERC riser
• IDSDM/vFlash module card
• Internal USB key (if installed)
• Processors and heat sink modules
• Memory modules
• LOM riser card

Follow the below steps to remove the System Board:

1. Disconnect all cables from the system board.

OTE

Ensure that you note the routing of the cables as you remove them from the

system board.

CAUTION: Take care not to damage the system identification button while removing the
system board from the chassis.

CAUTION: Do not lift the system board by holding a memory module, processor, or other
components.

2. Using a Phillips #2 screwdriver, remove the screws that secure the system board to the
chassis.

3. Hold the system board holder, slightly lift the system board, and then slide it toward the
front of the chassis.

4. Using the system board holder, lift the system board out of the chassis.

Installing the System Board

Follow the safety guidelines listed in

Safety instructions

Installing and Removing System Components

System Board

100

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды