Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 84

Страница: 84 / 120

Remove all hard drives from the hard drive slot.

Disconnect all the cables from the backplane.

Follow the below steps to remove the hard drive backplane:

1. Press the blue release tabs and lift the backplane to disengage the backplane from the
hooks on the system.

2. To remove a backplane with an expander board:

a. Loosen the captive screws that secure the expander board.

a. Press the release tabs and lift the backplane to disengage the slots on the

backplane from the hooks on the system.

3. Lift the backplane out of the system.

Installing and Removing System Components

Hard drive backplane

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды