Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 77

Страница: 77 / 120

Optional MicroSD or vFlash card

Removing the MicroSD card

Follow the safety guidelines listed in

Safety instructions

Follow the procedure listed in

Before working inside your system

Follow the below steps to remove a MicroSD card:

1. Locate the MicroSD card slot on the vFlash/IDSDM module, and press the card to partially
release it from the slot. To locate IDSDM/vFlash module, see the System board jumpers and
connectors section.

2. Hold the MicroSD card and remove it from the slot.

OTE

Temporarily label each MicroSD card with its corresponding slot number after

removal.

After removing the MicroSD card you could do the following:

1. Follow the procedure listed in

After working inside your system

2. Install a MicroSD card.

Installing the MicroSD card

Follow the safety guidelines listed in

Safety instructions.

OTE

To use an MicroSD card with your system, ensure that the Internal SD Card

Port is enabled in System Setup.

Installing and Removing System Components

Optional MicroSD or vFlash card

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды