Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 81

Страница: 81 / 120

After removing the LOM riser card you could do the following:

Install the LOM riser card.

Installing the LOM riser card

Follow the safety guidelines listed in

Safety instructions

Follow the below steps to install the LOM riser card:

1. Align the connectors on the LOM riser card with the slot on the system.

2. Press the LOM riser card until the card is firmly seated on the system board connector and
the two blue plastic snap hold the LOM riser card in place.

3. Using a Phillips #2 screwdriver, replace the screws to secure the LOM riser card to the
system board.

After installing the LOM riser card you could do the following:

If removed, install the risers.

Follow the procedure listed in

After working inside your system.

Installing and Removing System Components

LOM riser card

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды