Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 36

Страница: 36 / 120

Backplane Cover

This describes the procedure to install and remove the Backplane Cover.

Removing the backplane cover

Follow the safety guidelines listed in

Safety instructions

Follow the procedure listed in

Before working inside your system

Remove the system cover.

Follow the below steps to remove the Backplane Cover.

1. Slide the backplane cover in the direction of the arrows marked on the backplane cover.

2. Lift the backplane cover away from the system.

Installing the backplane cover

Follow the safety guidelines listed in

Safety instructions

Follow the procedure listed in

Before working inside your system.

Install the system cover.

Follow the below steps to install the Backplane Cover.

1. Align the tabs on the backplane cover with the guide slots on the system.

2. Slide the backplane cover toward the front of the system until the cover locks into place.

Installing and Removing System Components

Backplane Cover

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды