Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 39

Страница: 39 / 120

Follow the procedure listed in

After working inside your system

Cooling Fans

This describes the procedure to install and remove the Cooling Fan.

Removing the Cooling Fan

Follow the safety guidelines listed in

Safety instructions

Follow the procedure listed in

Before working inside your system

Remove the air shroud.

Remove the internal riser.

Disconnect the fan cable from the system board.

Move the cables out of the way to access the cooling fan cable connector on the system
board.

Follow the below steps to remove the Cooling Fan:

1. Press the tabs on the side of the cable connector to disconnect the cable from the
connector on the system board.

OTE

Ensure that you disconnect the fan 1 cable from the power interposer board.

Ensure that you note the routing of the cables as you remove them from the system
board.

2. Lift the fan out holding the blue touch point.

Installing and Removing System Components

Cooling Fans

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды