Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 82

Страница: 82 / 120

Hard drive backplane

Hard drive backplane details

Depending on your system configuration, the hard drive backplanes supported in hardware
appliance are listed here:

System

Supported hard drives options

GigaVUE-FM Hardware Appliance 2.5-inch (x8) SAS, SATA or Nearline SAS drives

Figure 1

8 x 2.5-inch backplane

1.Release tab

2. SATA_A cable connector

3. backplane signal cable connector

4. backplane

5. SATA_B cable connector

6. backplane power cable connector

Installing the hard drive backplane

Follow the safety guidelines listed in

Safety instructions

OTE

The procedure to install the backplane is similar for all backplane

configurations.

Follow the below steps to install the hard drive backplane:

1. Align the slots on the backplane with the hooks on the system.

2. Lower the hard drive backplane until the blue release tabs snap into place.

3. If your backplane has an expander board, then tighten the captive screws to secure the
expander board to the system.

Installing and Removing System Components

Hard drive backplane

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды