Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 32

Страница: 32 / 120

4. Turn on the attached peripherals and then turn on the system.

Recommended tools

You need the following tools to perform the removal and installation procedures:

●

Key to the bezel lock.The key is required only if your system includes a bezel.

●

Phillips #1 screwdriver

●

Phillips #2 screwdriver

●

Torx #T30 screwdriver

●

Torx #T8 screwdriver

●

Wrist grounding strap

Front Bezel (Optional)

This describes the procedure to install and remove the optional Front Bezel.

Removing the front bezel

The procedure to remove the front bezel with and without the LCD panel is the same.

Follow the safety guidelines listed in

Safety instructions.

1. Unlock the bezel by using the bezel key.

2. Press the release button, and pull the left end of the bezel.

3. Unhook the right end, and remove the bezel.

Installing the front bezel

The procedure to install the front bezel with and without the LCD panel is the same.

Follow the safety guidelines listed in

Safety instructions

1. Locate and remove the bezel key.

OTE

The bezel key is part of the LCD bezel package.

Installing and Removing System Components

Front Bezel (Optional)

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды