Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 45

Страница: 45 / 120

CAUTION

: When a replacement hot swappable drive is installed and the system is

powered on, the drive automatically begins to rebuild. Ensure that the replacement drive
is blank or contains data that you wish to overwrite. Any data on the replacement drive is
immediately lost after the drive is installed.

Follow the safety guidelines listed in

Safety instructions

If applicable, remove the hard drive blank.

Follow the below steps to install the Hard Drive:

1. Press the release button on the front of the hard drive carrier to open the release handle.

2. Insert the hard drive carrier into the hard drive slot and slide until the hard drive connects
with the backplane.

3. Close the hard drive carrier release handle to lock the hard drive in place.

After installing the Hard Drive if applicable, install the front bezel.

Removing the Drive from the Drive Carrier

CAUTION: Mixing drives from previous generations of PowerEdge servers is not
supported.

Follow the below steps to remove the Drive from Drive Carrrier:

1. Using a Phillips #1 screwdriver, remove the screws from the slide rails on the drive carrier.

2. Lift the drive out of the drive carrier.

Installing and Removing System Components

Drives

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды