Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 42

Страница: 42 / 120

3. Connect the intrusion switch cable to the connector on the system board.

After installing the Intrusion Switch ensure the following:

1. Install internal PERC riser.

2. Follow the procedure listed in

After working inside your system

Drives

This describes the procedure to install and remove the Drives.

Removing a Drive Blank

Follow the safety guidelines listed in

Safety instructions

If installed, remove the front bezel.

CAUTION: To maintain proper system cooling, drive blanks must be installed in all empty
drive slots.

CAUTION: Mixing drive blanks from previous generations of PowerEdge servers is not
supported.

Follow the below steps to remove the Drive Blank:

1. Press the release button, and slide the drive blank out of the drive slot.

After removing the Drive Blank ensure the following:

1. Install a drive or Installing the hard drive backplane.

Installing a drive blank

Follow the safety guidelines listed in

Safety instructions

If installed, remove the front bezel.

Installing and Removing System Components

Drives

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды