Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 41

Страница: 41 / 120

Removing the Intrusion Switch

Follow the safety guidelines listed in

Safety instructions

Follow the procedure listed in

Before working inside your system

Remove air shroud.

Remove internal PERC riser.

Follow the below steps to remove the Intrusion Switch:

1. Disconnect the intrusion switch cable connected to the system board.

OTE

Ensure that you note the routing of the cables as you remove them from the

system board.

2. Slide the intrusion switch out of the intrusion switch slot.

Installing the intrusion switch

Follow the safety guidelines listed in

Safety instructions

Follow the procedure listed in

Before working inside your system

Follow the below steps to install the Intrusion Switch:

1. Align the intrusion switch with the intrusion switch slot.

2. Slide the intrusion switch until it is firmly seated in the intrusion switch slot.

Installing and Removing System Components

Intrusion Switch

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды