Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 33

Страница: 33 / 120

2. Align and insert the tabs on the bezel into the slots on the system.

3. Press the bezel until the button clicks in place.

4. Lock the bezel by using the key.

System cover

This describes the procedure to install and remove the System Cover.

Removing the system cover

Follow the safety guidelines listed in

Safety instructions

Turn off the system, including any attached peripherals.

Disconnect the system from the electrical outlet and disconnect the peripherals.

Follow the below steps to remove the System Cover.

1. Using a 1/4 inch flat head or a Phillips #2 screwdriver, rotate the latch release lock counter
clockwise to the unlocked position.

2. Lift the latch till the system cover slides back and the tabs on the system cover disengage
from the guide slots on the system.

3. Hold the cover on both sides, and lift the cover away from the system.

Installing and Removing System Components

System cover

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды