Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 40

Страница: 40 / 120

Installing Cooling Fan

Follow the safety guidelines listed in

Safety instructions

Follow the procedure listed in

Before working inside your system

Remove the air shroud.

Remove the internal riser.

Remove the power cable.

Move the cables out of the way to access the cooling fan cable connector on the system
board.

Follow the below steps to install the Cooling Fan:

1. Holding the blue touch point, place the cooling fan into the cooling fan cage.

2. Route the cooling fan cable and connect it to the connector on the system board.

After installing the Cooling Fan ensure the following:

1. Install the internal riser.

2. Connect the power cable.

3. Ensure all the cables are routed correctly.

4. Install the air shroud.

5. Follow the procedure listed in

After working inside your system

Intrusion Switch

This describes the procedure to install and remove the Intrusion Switch.

Installing and Removing System Components

Intrusion Switch

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды