Gigamon GFM-HW1-FM001-HW Скачать руководство пользователя страница 73

Страница: 73 / 120

Follow the below steps to remove an Expansion Card from Expansion Card Riser:

Install the expansion card riser.

Installing the Expansion Card into the Expansion Card Riser

Follow the safety guidelines listed in

Safety instructions

If installing a new expansion card, unpack it and prepare the card for installation.

OTE

For instructions, see the documentation accompanying the card.

Remove the expansion card riser.

Follow the below steps to install an Expansion Card from the Expansion Card Riser:

1. Open the PCIe card holder latch.

2. If installed, remove the filler bracket.

OTE

Store the filler bracket for future use. Filler brackets must be installed in empty

expansion card slots to maintain Federal Communications Commission (FCC)
certification of the system. The brackets also keep dust and dirt out of the system and
aid in proper cooling and airflow inside the system.

Installing and Removing System Components

Expansion cards and expansion card risers

GigaVUE-FM Hardware Appliance Guide for GFM-HW1-FM010 and GFM-HW1-FM001-HW

Содержание GFM-HW1-FM001-HW

























































































































Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды

Gigamon GFM-HW1-FM001-HW, Руководство по оборудованию

Результаты поиска

Содержание GFM-HW1-FM001-HW

Отзывы:

Похожие инструкции для GFM-HW1-FM001-HW

Бренды по названию

Популярные бренды