GigaDevice Semiconductor GD32F20 Series Скачать руководство пользователя страница 856

Страница: 856 / 950

GD32F20x User Manual

856

Bits

Fields

Descriptions

31:6

Reserved

Must be kept at reset value

TMSARU

Time stamp addend register update bit

This bit is cleared when the update is completed. This register bit must be read as

zero before application set it.

0: The timestamp addend register’s contents are not updated to the PTP block for

fine correction

1: The timestamp addend register’s contents are updated to the PTP block for fine

correction

TMSITEN

Timestamp interrupt trigger enable bit

0: Disable timestamp interrupt

1: A timestamp interrupt is generated when the system time becomes greater than

the value written in target time register.

Note:

When the timestamp trigger interrupt generated, this bit is cleared

TMSSTU

Timestamp system time update bit

Both the TMSSTU and TMSSTI bits must be read as zero before application set this

bit

0: The system time is maintained without any change

1: The system time is updated (added to or subtracted from) with the value specified

in the timestamp update (high and low) registers. It is cleared by hardware when

the update finished.

TMSSTI

Timestamp system time initialize bit

This bit must be read as zero before application set it.

0: The system time is maintained without any change

1: Initializing the system time with the value in timestamp update (high and low)

registers. It is cleared by hardware when the initialization finished.

TMSFCU

Timestamp fine or coarse update bit

0:The system timestamp uses the coarse method for updating

1:The system timestamp uses the fine method for updating

TMSEN

Timestamp enable bit

0: Disable timestamp function

1: Enable timestamp function for transmit and receive frames

Note:

After setting this to 1, application must initialize the system time.

27.4.34.

PTP subsecond increment register (ENET_PTP_SSINC)

Address offset: 0x0704

Reset value: 0x0000 0000

This register configures the 8-bit value for the incrementing subsecond register. In coarse

mode, this value is added to the system time every HCLK clock cycle. In fine mode, this value

is added to the system time when the accumulator reaches overflow.

Содержание GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32F20 Series

Отзывы:

Похожие инструкции для GD32F20 Series

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32F20 Series, Руководство пользователя

Результаты поиска

Содержание GD32F20 Series

Отзывы:

Похожие инструкции для GD32F20 Series

Бренды по названию

Популярные бренды