manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, Руководство пользователя

Поделиться
Скачать
GigaDevice Semiconductor GD32F20 Series Скачать руководство пользователя страница 473

 

                                                                                                             

GD32F20x User Manual

 

473 

 

This bit cannot be modified when PROT [1:0] bit-filed in TIMERx_CCHP register is 

11 and CH0MS bit-filed is 00(COMPARE MODE). 

3 

CH0COMSEN 

Channel 0 compare output shadow enable 

When this bit is set, the shadow register of TIMERx_CH0CV register, which 

updates at each update event, will be enabled.   

0: Channel 0 output compare shadow disable 

1: Channel 0 output compare shadow enable 

The PWM mode can be used without validating the shadow register only in single 

pulse mode (SPM bit in TIMERx_CTL0 register is set). 

This bit cannot be modified when PROT [1:0] bit-filed in TIMERx_CCHP register is 

11 and CH0MS bit-filed is 00. 

2 

CH0COMFEN 

Channel 0 output compare fast enable 

When this bit is set, the effect of an event on the trigger in input on the 

capture/compare output will be accelerated if the channel is configured in PWM0 

or PWM1 mode. The output channel will treat an active edge on the trigger input 

as a compare match, and CH0_O is set to the compare level independently from 

the result of the comparison. 

0: Channel 0 output quickly compare disable. The minimum delay from an edge 

on the trigger input to activate CH0_O

 

output is 5 clock cycles. 

1: Channel 0 output quickly compare enable. The minimum delay from an edge on 

the trigger input to activate CH0_O

 

output is 3 clock cycles. 

1:0 

CH0MS[1:0] 

Channel 0 I/O mode selection 

This bit-field specifies the work mode of the channel and the input signal selection. 

This bit-field is writable only when the channel is not active. (CH0EN bit in 

TIMERx_CHCTL2 register is reset).). 

00: Channel 0 is configured as output 

01: Channel 0 is configured as input, IS0 is connected to CI0FE0 

10: Channel 0 is configured as input, IS0 is connected to CI1FE0 

11: Channel 0 is configured as input, IS0 is connected to ITS. This mode is 

working only if an internal trigger input is selected through TRGS bits in 

TIMERx_SMCFG register. 

Input capture mode: 

Bits

 

Fields

 

Descriptions 

31:8 

Reserved 

Must be kept at reset value. 

7:4 

CH0CAPFLT[3:0] 

Channel 0 input capture filter control 

An event counter is used in the digital filter, in which a transition on the output 

occurs after N input events. This bit-field specifies the frequency used to sample 

CI0 input signal and the length of the digital filter applied to CI0. 

0000: Filter disabled, f

SAMP

=f

DTS

, N=1 

0001: f

SAMP

=f

TIMER_CK

, N=2 

0010: f

SAMP

= f

TIMER_CK

, N=4 

Содержание GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды