GigaDevice Semiconductor GD32F20 Series Скачать руководство пользователя страница 427 | Manualshive

Страница: 427 / 950

background image

GD32F20x User Manual

427

18.3.3.

Block diagram

Figure 18-50. General level1 timer block diagram

provides details on the internal

configuration of the general level1 timer.

Figure 18-50. General level1 timer block diagram

Input Logic

Synchronizer&Filter

&Edge Detector

Edge selector

Prescaler

Trigger processor

Trigger Selector&Counter

Quadrate Decoder

Slave mode processor

Counter

TIMERx_CHxCV

Register /Interrupt

Register set and update

Interrupt collector and

controller

APB BUS

CK_TIMER

CH0_IN

CH1_IN

CI0

ITI0

ITI1

ITI2

ITI3

CAR

Output Logic

generation of outputs signals in
compare, PWM,and mixed modes
according to initialization, software
output mask, and polarity control

CH0_O

TIMERx_TRGO

Interrupt

CH1_O

Update

Trigger

Cap/Com

CI1

PSC

PSC_CLK

TIMER_CK

18.3.4.

Function overview

Clock selection

The general level1 TIMER has the capability of being clocked by either the CK_TIMER or an

alternate clock source controlled by SMC (TIMERx_SMCFG bit [2:0]).



SMC [2:0] == 3’b000. Internal timer clock CK_TIMER which is from module RCU.

The default internal clock source is the CK_TIMER used to drive the counter prescaler when
the slave mode is disabled (SMC [2:0] == 3’b000). When the CEN is set, the CK_TIMER will

be divided by PSC value to generate PSC_CLK.

In this mode, the TIMER_CK,

driven counter’s prescaler to count, is equal to CK_TIMER

which is from RCU.

If the slave mode controller is enabled by setting SMC [2:0] in the TIMERx_SMCFG register

to an available value including 0x1, 0x2, 0x3 and 0x7, the prescaler is clocked by other clock

sources selected by the TRGS [2:0] in the TIMERx_SMCFG register and described as follows.

When the slave mode selection bits SMC are set to 0x4, 0x5 or 0x6, the internal clock

TIMER_CK is the counter prescaler driving clock source.

«
...
425
426
427
428
429
...
»

Содержание GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GD32F20 Series

Бренд: Falcon Страницы: 3

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

PetroVend PV200

Бренд: OPW Страницы: 2

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

DIGITAL EPIC-2 DTM

Бренд: Westlock Страницы: 33

Бренд: YASKAWA Страницы: 360

Бренд: Beckhoff Страницы: 67

Бренд: Omron Страницы: 12

Бренд: OCTANORM Страницы: 6

Бренд: PacComm Страницы: 29

Smart Pass FPS-1000R

Бренд: AHA Страницы: 36

Бренд: Vega Страницы: 28

Бренд: WAC Страницы: 5

Бренд: Napoleon Страницы: 8

NEO Agility 48 10GbE Card

Бренд: Overland Storage Страницы: 4

Бренд: blackloud Страницы: 27

Бренд: Toky Страницы: 4

Бренд: Flowserve Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды