Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 226

background image

3500/42 Operation and Maintenance

Configuration Information

13

Channel Pair 1 and 2
Channel Pair 3 and 4
The fields within these boxes pertain to both channels of the channel pair.

Channel Pair Type
The type of monitoring which is to be performed by the channel pair. The
following Channel Pair types are available in the monitor:

- Radial Vibration
- Thrust Position
- Differential Expansion
- Eccentricity
- Acceleration
- Velocity

Keyphasor



Association

No Keyphasor
Can be used when a Keyphasor is not available. If this is marked then
the only data that will be available is Direct and Gap. This field will
automatically be marked for channel pairs which do not require a
Keyphasor transducer (for example Thrust Position and Differential
Expansion).

Primary
The Keyphasor channel selected that is normally used for measurement.
When this Keyphasor transducer is marked invalid, the backup
Keyphasor transducer will provide the shaft reference information.

Backup
The Keyphasor channel selected that will be used if the primary
Keyphasor fails. If you do not have a backup Keyphasor, select the same
Keyphasor channel as the primary Keyphasor.

Active
Select whether the functions of the channel will be turned on (

) or off (

).

Options
A button to display the configuration options for the selected channel type.

Note

For TMR applications, set Channel Pair 1 and 2 as primary Keyphasor
and Channel Pair 3 and 4 as backup Keyphasor.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
18
19
20
21
22
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Nabco Страницы: 35

Бренд: National Instruments Страницы: 8

Бренд: Parker Страницы: 42

Бренд: Burlington Страницы: 7

Бренд: Nordelettronica Страницы: 8

ibaMS16-DI-220V Series

Бренд: IBA Страницы: 32

Бренд: A & H Страницы: 35

Бренд: Cypress Страницы: 2

MEMO CORE CONTROL

Бренд: MegaLite Страницы: 11

Бренд: Hanma Страницы: 3

Бренд: Phylrich Страницы: 3

Apollo 70-600 Series

Бренд: Conbraco Industries Страницы: 4

Бренд: Ravel Страницы: 33

Бренд: Walther Страницы: 20

Бренд: AMALGAMATED INSTRUMENT Страницы: 27

Бренд: HBC Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды