Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 226

background image

3500/42 Operation and Maintenance

Maintenance

157

If a low-pass filter is configured and no high-pass filter is configured, use HPF

= 3 Hz

If a high-pass filter is configured and no low-pass filter is configured, use LPF

= 5,500 Hz

Set the frequency of the function generator to this new value. The above is
done to obtain a test frequency in the center of the channel frequency range.

3. Adjust the function generator amplitude to produce a reading that is below

the Direct setpoint levels on the Direct bar graph display of the Verification
screen.

4. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

OK LED is on, the bar graph indicator for Direct is green, and the Current
Value field contains no alarm indication.

5. Adjust the function generator amplitude such that the signal just exceeds the

Direct Over Alert/Alarm 1 setpoint level. Wait for 2 or 3 seconds after the
alarm time delay expires and verify that the bar graph indicator for Direct
changes color from green to yellow and the Current Value Field indicates an
Alarm.

6. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for Direct remains yellow and that the Current Value Field
still indicates an Alarm.

7. Adjust the function generator amplitude such that the signal just exceeds the

Direct Over Danger/Alarm 2 setpoint level. Wait for 2 or 3 seconds after the
alarm time delay expires and verify that the bar graph indicator for Direct
changes color from yellow to red and that the Current Value Field indicates
an Alarm.

8. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for Direct remains red and that the Current Value Field
still indicates an Alarm.

9. Adjust the function generator amplitude such that the signal reads below the

Over Alarm setpoint levels. If the nonlatching option is configured, observe
that the bar graph indicator for Direct changes color to green and that the
Current Value Box contains no indication of alarms. Press the RESET switch
on the Rack Interface Module (RIM) to reset latching alarms.

10. If you can not verify any configured alarm, recheck the configured setpoints.

If the monitor still does not alarm properly or fails any other part of this test,
go to Section 5.1.11 (If a Channel Fails a Verification Test).

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
162
163
164
165
166
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: YASKAWA Страницы: 256

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Van Air Страницы: 4

Бренд: GBD Страницы: 15

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

Бренд: National Instruments Страницы: 78

Бренд: Audioaccess Страницы: 2

Liquitron DP5000-01A

Бренд: LMI Technologies Страницы: 28

Бренд: Motrona Страницы: 10

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

MISTCATCH OMC-ATW-N2-AW

Бренд: OHM ELECTRIC Страницы: 8

SmartConnect SCM-NM

Бренд: Zeta Alarm Limited Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды