Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 226

background image

Maintenance

3500/42 Operation and Maintenance

100

5.1.5.2

Test Alarms - Radial Vibration

The general approach for testing alarm setpoints is to simulate the vibration and
Keyphasor® signal with a function generator. The alarm levels are tested by
varying the vibration signal (both peak to peak amplitude and DC voltage bias)
and observing that the correct results are reported in the Verification screen on
the test computer. It is only necessary to test those alarm parameters that are
configured and being used. The general test procedure to verify current alarm
operation will include simulating a transducer input signal and varying this signal:
1. to exceed over Alert/Alarm 1 and Danger/Alarm 2 Setpoints, and
2. to drop below any under Alert/Alarm 1 and Danger/Alarm 2 Setpoints and
3. to produce a nonalarm condition.

When varying the signal from an alarm condition to a nonalarm condition, alarm
hysteresis must be considered. Adjust the signal well below the alarm setpoint
for the alarm to clear.

Direct

1. Disconnect PWR, COM, and SIG field wiring from the channel terminals on

the I/O module.

2. Connect test equipment and run software as described in Section 5.1.5.1

(Test Equipment and Software Setup - Radial Vibration).

3. Set the Keyphasor multiplier/divider so that the multiply setting is one and the

divide setting is one. Adjust the function generator amplitude to produce a
reading that is below the Direct setpoint levels on the Direct bar graph display
of the Verification screen.

4. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

OK LED is on, the bar graph indicator for Direct is green, and the Current
Value field contains no alarm indication.

5. Adjust the function generator amplitude such that the signal just exceeds the

Direct Over Alert/Alarm 1 setpoint level. Wait for 2 or 3 seconds after the
alarm time delay expires and verify that the bar graph indicator for Direct
changes color from green to yellow and that the Current Value Field indicates
an Alarm.

6. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for Direct remains yellow and that the Current Value Field
still indicates an Alarm.

7. Adjust the function generator amplitude such that the signal just exceeds the

Direct Over Danger/Alarm 2 setpoint level. Wait for 2 or 3 seconds after the
alarm time delay expires and verify that the bar graph indicator for Direct
changes color from yellow to red and that the Current Value Field indicates
an Alarm.

8. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for Direct remains red and that the Current Value Field

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
105
106
107
108
109
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: Eaton Страницы: 16

Бренд: Abus Страницы: 12

Бренд: Yudian Страницы: 26

Бренд: Harmonic Drive Страницы: 85

Бренд: Sanhua Страницы: 3

Бренд: Samson Страницы: 6

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

Бренд: K&G GROEP Страницы: 27

Бренд: CAME Страницы: 2

Бренд: CalAmp Страницы: 13

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Waukesha Cherry-Burrell D4 Series

Бренд: SPX FLOW Страницы: 34

Бренд: Cypress Страницы: 3

IB-TRON 4000 SOL

Бренд: INSBUD Страницы: 14

Бренд: Quickie Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды