manualshive.com logo in svg

Bently Nevada PROXIMITOR 3500/42, Руководство по эксплуатации и обслуживанию, Страница: 65 / 226

Поделиться
Скачать
Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 65

Configuration Information

3500/42 Operation and Maintenance

58

- Monitors must be configured in channel pairs (for example, Channels 1 and 2

may be configured as Velocity and Channels 3 and 4 may be configured as
Thrust Position).

- When integration is selected, the available Direct Full-scale Ranges will change

to reflect this.

- When band-pass filtering is selected, the high-pass and low-pass filters must be

set a minimum of a decade apart.

- The 100ms danger alarm is only available for the Velomitor and High

Temperature Velomitor options.

- When a single or dual channel of velocity is activated, the maximum channel

frequency supported is as shown:

Configuration Settings

Channel

Frequencies

Filtering

RMS

Integration

3 to 5500 Hz

---

No

---

10 to 5500 Hz

---

Yes

---

** dashes represent both yes and no

 

- The Latching OK Mode and the Timed OK Channel Defeat options are not

compatible.

- If a Non-Standard transducer is selected, the setpoint OK limits are set to ±1

volt from the Upper and Lower OK limits that are selected.

- If the monitor is configured to alarm on high velocity conditions on a

reciprocating machine, it is recommended that you disable the Timed
OK/Channel Defeat option.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов