Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 218

Страница: 218 / 226

3500/42 Operation and Maintenance

Specifications

211

SIGNAL CONDITIONING

Specified at +25

C (77

Radial Vibration

Frequency Response:

Direct Filter:

Gap Filter:

*Not 1X Filter:

*Smax:

*,**1X & 2X Vector Filter:

User-programmable for 4 to 4,000 Hz or 1
to 600 Hz.

-3 dB at .09 Hz.

60 cpm to 16 times running speed.
Constant Q notch filter. Minimum rejection
in stopband of –34.9 dB.

0.125 to 16 times running speed.

Constant Q Filter. Minimum rejection in
stopband of -57.7 dB.

* Note - 1X & 2X Vector, Not 1X, and Smax parameters are valid for
machine speeds of 60 to 60,000 cpm.

**Note - Minimum Signal Amplitude for Phase measurement is 42.7 mV

Accuracy:

Direct and Gap:

1X & 2X:

Smax:

Not 1X:

Within

0.33 % of full scale typical,

1 %

maximum.

Within

0.33 % of full scale typical,

1 %

maximum.

Within

5 % maximum.

3 % for machine speeds less than 30,000

cpm.

8.5 % for machine speeds greater

than 30,000 cpm.

Thrust and Differential Expansion:

Frequency Response:

Direct Filter:
Gap Filter:

Accuracy:

-3 dB at 1.2 Hz.
-3 dB at 0.41 Hz.

Within

0.33 % of full scale typical,

1 %

maximum.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PROXIMITOR 3500/42



































































































































































































































Результаты поиска

Содержание PROXIMITOR 3500/42

Отзывы:

Bently Nevada PROXIMITOR 3500/42, Руководство по эксплуатации и обслуживанию, Страница: 218 / 226

Результаты поиска

Содержание PROXIMITOR 3500/42

Отзывы: