Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 226

background image

3500/42 Operation and Maintenance

Maintenance

179

To Input Peak to Peak Volts for Peak Units

5.1.9.7

Test OK Limits – Acceleration

Note

If the Danger Bypass has been activated, then the BYPASS LED will be on.
All other channels in the rack must be OK or bypassed for the OK relay to be
energized.

The general approach for testing OK limits is to input a DC voltage and adjust it
above the Upper OK limit and below the Lower OK limit. This should cause a not
OK condition and cause the OK Relay to change state. The Upper and Lower
OK limits are displayed in the Verification screen on the test computer.

1. Disconnect PWR, COM, and SIG field wiring from the channel terminals on

the I/O module.

2. Connect test equipment and run software as described in Section 5.1.9.1

(Test Equipment and Software Setup - Acceleration).

3. Bypass all other configured channels.

4. Adjust the power supply voltage to -7.00 Vdc.

5. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

monitor OK LED is on and that the Channel OK State line in the Channel
Status section of the Verification Display screen reads OK.

6. Verify that the OK relay on the Rack Interface I/O Module indicates OK

(energized). See 3500/20 Rack Interface Module manual, part #129768-01.

7. Increase the power supply voltage (more negative) until the OK LED just

goes off (upper limit). Verify that the Channel OK State line on the
Verification screen reads not OK and that the OK Relay indicates not OK.
Verify that the Upper OK limit voltage displayed on the Verification screen is
equal to or more positive than the input voltage.

8. Decrease the power supply voltage (less negative) to -7.00 Vdc.

9. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

OK LED comes back on and the OK relay energizes. Verify that the Channel
OK State line in the Channel Status section reads OK.

Input

Voltage

(V pp)

=

1

30.72

0.1

x 1 = 0.9207 V pp















/

.

282 84

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
184
185
186
187
188
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: wattio Страницы: 20

Бренд: Jafar Страницы: 10

Бренд: Jafar Страницы: 8

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Radarcan Страницы: 40

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Digiplex DGP-848

Бренд: Paradox Страницы: 20

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

Бренд: Vega Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды