manualshive.com logo in svg

Bently Nevada PROXIMITOR 3500/42, Руководство по эксплуатации и обслуживанию, Страница: 78 / 226

Поделиться
Скачать
Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 78

3500/42 Operation and Maintenance

Configuration Information

71

Monitor Alarm Bypass

When enabled, the monitor does not perform alarming functions.  All
proportional values are still provided.  The monitor switch number is used in
the Communication Gateway and Display Interface Modules.

Monitor Switch Number

Switch Name

1

Configuration Mode

3

Monitor Alarm Bypass

Channel Switches

Alert Bypass
When enabled, the channel does not perform Alert alarming functions.

Danger Bypass
When enabled, the channel does not perform Danger alarming functions.

Special Alarm Inhibit
When enabled, all nonprimary Alert alarms are inhibited.

Bypass
When enabled, the channel provides no alarming functions and supplies no
proportional values.

The channel switch number is used in the Communication Gateway and Display
Interface Modules.

Channel Switch Number

Switch Name

1

Alert Bypass

2

Danger Bypass

3

Special Alarm Inhibit

4

Bypass

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов