manualshive.com logo in svg

Bently Nevada PROXIMITOR 3500/42, Руководство по эксплуатации и обслуживанию, Страница: 122 / 226

Поделиться
Скачать
Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 122

3500/42 Operation and Maintenance

Maintenance

115

1X Phase

Note

If the test equipment is not capable of changing the phase output to a known
value, use the following procedure.  If your test equipment can change the
phase output to a known value, use the procedure on page 116.

1. Disconnect PWR, COM, and SIG field wiring from the channel terminals on

the I/O module.

2. Connect test equipment and run software as described in Section 5.1.5.1

(Test Equipment and Software Setup - Radial Vibration).  Set the Keyphasor
multiplier/divider so that the multiply setting is one and the divide setting is
one.

3. Attach one channel of a two channel oscilloscope to the vibration signal

buffered output and attach the other channel to the associated Keyphasor

®

signal buffered output and observe the two signals simultaneously.

4. Measure the phase.  1X Phase will be measured from the leading edge of the

Keyphasor

®

 pulse to the first positive peak of the vibration signal. See the

example below (on page 115) which illustrates a phase of 45

°

.  Observe the

1X Phase bar graph display and Current Value Box; it should read
approximately what was measured above.

Example:

1X = one cycle of vibration signal per shaft revolution.

5. Disconnect the test equipment and reconnect the PWR, COM, and SIG field

wiring to the channel terminals on the I/O module.  Verify that the OK LED
comes on and the OK relay energizes.  Press the RESET switch on the Rack

one cycle

0

°

360

°

Phase
Lag= 45

°

1X
Vibration
Signal

Time

Keyphasor

Signal

one shaft revolution

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов