Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 199 | Manualshive

Страница: 199 / 226

background image

Troubleshooting

3500/42 Operation and Maintenance

192

6. Troubleshooting

This section describes how to troubleshoot a problem with the
Proximitor®/Seismic Monitor or the I/O module by using the information provided
by the self-test, the LED’s, the System Event List, and the Alarm Event List.

6.1 Self-test

To perform the Proximitor/Seismic Monitor self-test:

1. Connect a computer running the Rack Configuration Software to the 3500

rack (if needed).

2. Select Utilities from the main screen of the Rack Configuration Software.

3. Select System Events/Module Self-test from the Utilities menu.

4. Press the Module Self-test button on the System Events screen.

Application Alert

Machinery protection will
be lost while the self-test
is being performed.

5. Select the slot that contains the Proximitor/Seismic Monitor and press the OK

button. The Proximitor/Seismic Monitor will perform a full self-test and the
System Events screen will be displayed. The list will not contain the results
of the self-test.

6. Wait 30 seconds for the module to run a full self-test.

7. Press the Latest Events button. The System Events screen will be updated

to include the results of the Proximitor/Seismic Monitor self-test.

8. Verify if the Proximitor/Seismic Monitor passed the self-test. If the monitor

failed the self-test, refer to Section 6.3 (System Event List Messages).

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
197
198
199
200
201
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: Datavideo Страницы: 17

Бренд: Datamax Страницы: 22

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

Бренд: GE Страницы: 32

SYSVRF AHU 10HP S

Бренд: SystemAir Страницы: 16

Бренд: Zapi Страницы: 30

Бренд: EOS Страницы: 7

Бренд: UniPOS Страницы: 6

BLEUBOX R-IN-UHF-5239U

Бренд: iDTRONIC Страницы: 13

Бренд: Konig Страницы: 8

Бренд: Parallax Страницы: 3

Бренд: G-Tech Страницы: 26

972LM Security?

Бренд: Chamberlain Страницы: 4

Standard 22 GYRO COMPASS

Бренд: Raytheon Anschütz Страницы: 104

Бренд: W.E.S.T. Elektronik Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды