Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 226

Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 53

Configuration Information

3500/42 Operation and Maintenance

46

Scale Factor

Transducer

Without

Barriers

With Bently

Nevada Internal

Barriers

Standard I/O

With

Barriers

Discrete TMR

I/O With
Barriers

Bussed TMR

I/O With
Barriers

3300 5 and 8 mm
7200 5 and 8 mm

200 mV/mil

200 mV/mil

192 mV/mil

200 mV/mil

199 mV/mil

7200 11 mm

100 mV/mil

*

*

*

*

7200 14 mm

100 mV/mil

*

*

*

*

3300 16 mm HTPS

100 mV/mil

*

*

*

*

Note: ±15 % scale factor adjustment allowed.

* Barriers are not supported with this transducer option.

OK Limits

Transducer

Upper

Lower

Center Gap Voltage

Without

Barriers

(V)

With

Barriers

(V)

Without

Barriers

(V)

With

Barriers

(V)

Without

Barriers

(V)

With

Barriers

(V)

3300 8 mm
3300 5 mm
7200 5 mm
7200 8 mm

-16.75

-16.75

-2.75

-2.75

-9.75

-9.75

7200 11 mm

-19.65

*

-3.55

*

-11.60

*

7200 14 mm

-16.75

*

-2.75

*

-9.75

*

3300 16 mm
HTPS

-16.75

*

-2.75

*

-9.75

*

* Barriers are not supported with this transducer option.

Note: With Barriers includes BNC Internal Barrier I/O Modules.

Transducer Jumper Status (on I/O Module)
Returns the position of the Transducer Jumper on the Proximitor/Seismic I/O
Module. Refer to Section 4.1 (Setting the I/O Jumper) for the function of this
jumper.

Alarm Mode
Latching
Once an alarm is active, it will remain active even after the proportional value
drops below the configured setpoint level. The channel will remain in alarm
until it is reset using one of the following methods:

- the reset switch on the front of the Rack Interface Module
- the contact on the Rack Interface I/O Module
- the Reset button in the Operator Display Software
- the reset command through the Communication Gateway Module
- the reset command through the Display Interface Module
- the reset command in the Rack Configuration Software

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
51
52
53
54
55
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов