Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 226

background image

Maintenance

3500/42 Operation and Maintenance

166

supply the buffered outputs on the front panel will be inverted in phase and will
have a different DC voltage than the input. This will not affect the actual vibration
readings in the Monitor.

The general approach for testing OK limits is to input a DC voltage and adjust it
above the Upper OK limit and below the Lower OK limit. This will cause a not
OK condition and the OK Relay to change state (de-energize). The Upper and
Lower OK limits are displayed in the Verification screen on the test computer.

1. Disconnect PWR, COM / A, and SIG / B field wiring from the channel

terminals on the I/O module.

2. Connect test equipment and run software as described in Section 5.1.8.1

(Test Equipment and Software Setup - Velocity), page 154.

3. Bypass all other configured channels.

4. Adjust the power supply voltage to -7.00 Vdc.

5. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

monitor OK LED is on and that the Channel OK State line in the Channel
Status section of the Verification screen reads OK.

6. Verify that the OK relay on the Rack Interface I/O Module indicates OK

(energized). See the 3500/20 Rack Interface Module Operation and
Maintenance Manual, part number 129768-01.

7. Increase the power supply voltage (more negative) until the OK LED just

goes off (lower limit due to the inversion on the I/O Module). Verify that the
Channel OK State line on the Verification screen reads not OK and that the
OK Relay indicates not OK. Verify that the Lower OK limit voltage displayed

on the Verification screen is equal to or more negative than the following
value.

8. Decrease the power supply voltage (less negative) to -7.00 Vdc.

9. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

OK LED comes back on and the OK relay energizes. Verify that the Channel
OK State line in the Channel Status section reads OK.

L o w e r O K

L im it V o lta g e

- 2 0 .8 4

-

V in p u t

≤

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
171
172
173
174
175
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: BEIER-Electronic Страницы: 22

Бренд: Bard Страницы: 8

Бренд: Bardiani Valvole Страницы: 35

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Saab Страницы: 4

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: Zeta Страницы: 44

Бренд: Saluki Страницы: 13

Бренд: Nemesis Страницы: 6

Бренд: Game ready Страницы: 24

Бренд: JASTEC Страницы: 18

Бренд: Hattersley Страницы: 2

Бренд: National Instruments Страницы: 6

Бренд: Wenglor Страницы: 44

Бренд: bluelab Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды