Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 226

background image

3500/42 Operation and Maintenance

Maintenance

101

still indicates an Alarm.

9. Adjust the function generator amplitude such that the signal reads below the

Over Alarm setpoint levels. If the nonlatching option is configured, observe
that the bar graph indicator for Direct changes color to green and that the
Current Value Box contains no indication of alarms. Press the RESET switch
on the Rack Interface Module (RIM) to reset latching alarms.

10. If you can’t verify any configured alarm, recheck the configured setpoints. If

the monitor still does not alarm properly or fails any other part of this test, go
to Section 5.1.11 (If a Channel Fails a Verification Test).

11. Disconnect the test equipment and reconnect the PWR, COM, and SIG field

wiring to the channel terminals on the I/O module. Verify that the OK LED
comes on and the OK relay energizes. Press the RESET switch on the Rack
Interface Module (RIM) to reset the OK LED.

12. Repeat steps 1 through 11 for all configured channels.

Gap

1. Disconnect PWR, COM, and SIG field wiring from the channel terminals on

the I/O module.

2. Connect test equipment and run software as described in Section 5.1.5.1

(Test Equipment and Software Setup - Radial Vibration).

3. Adjust the power supply to produce a voltage that is within the Gap setpoint

levels on the Gap bar graph display of the Verification screen.

4. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

OK LED is on, the bar graph indicator for Gap is green and that the Current
Value field has no alarm indication.

5. Adjust the power supply voltage such that the signal just exceeds the Gap

Over Alert/Alarm 1 setpoint level. Wait for 2 or 3 seconds after the alarm
time delay expires and verify that the bar graph indicator for Gap changes
color from green to yellow and that the Current Value Field indicates an
Alarm.

6. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for Gap remains yellow and that the Current Value Field
still indicates an Alarm.

7. Adjust the power supply such that the signal just exceeds the Gap Over

Danger/Alarm 2 setpoint level. Wait for 2 or 3 seconds after the alarm time
delay expires and verify that the bar graph indicator for Gap changes color
from yellow to red and that the Current Value Field indicates an Alarm.

8. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for Gap remains red and that the Current Value Field still
indicates an Alarm.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
106
107
108
109
110
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: Lawler Страницы: 2

Бренд: ZEHUS Страницы: 28

Бренд: Valfonta Страницы: 12

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

Бренд: WAM Страницы: 62

Бренд: walimex Страницы: 7

Бренд: Walchem Страницы: 2

Бренд: Walchem Страницы: 73

Бренд: Walchem Страницы: 126

Бренд: wallas Страницы: 2

Бренд: Xylem Страницы: 48

Бренд: Daihan Scientific Страницы: 11

Бренд: Fancom Страницы: 23

Бренд: Beninca Страницы: 7

Бренд: Haes Страницы: 42

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренд: TWR Lighting Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды