Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 200

Страница: 200 / 226

3500/42 Operation and Maintenance

Troubleshooting

193

6.2

LED Fault Conditions

The following table shows how to use the LED’s to diagnose and correct
problems.

OK Led

TX/RX

BYPASS

Condition

Solution

1 Hz

Monitor is not
configured, is in
Configuration Mode, or
in Calibration Mode.

Reconfigure the
Monitor, or exit
Configuration, or
Calibration Mode.

5 Hz

Monitor error

Check the System
Event List for severity.

Flashing

Module is operating
correctly

No action required.

OFF

Monitor is not operating
correctly or the
transducer has faulted
and has stopped
providing a valid signal.

Check the System
Event List and the
Alarm Event List.

2 Hz

Monitor is configured for
Timed OK Channel
Defeat and has been not
OK since the last time
the RESET button was
pressed.

Press the Reset
button on the Rack
Interface Module.
Check the System
Event List.

Not
flashing

Monitor is not operating
correctly.

Monitor is not
executing alarming
functions. Replace
immediately.

OFF

Alarm Enabled

No action required.

Some or all Alarming
Disabled

No action required.

= Behavior of the LED is not related to the condition.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PROXIMITOR 3500/42



































































































































































































































Результаты поиска

Содержание PROXIMITOR 3500/42

Отзывы:

Похожие инструкции для PROXIMITOR 3500/42

Бренды по названию

Популярные бренды

Bently Nevada PROXIMITOR 3500/42, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PROXIMITOR 3500/42

Отзывы:

Похожие инструкции для PROXIMITOR 3500/42

Бренды по названию

Популярные бренды