Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 226

background image

3500/42 Operation and Maintenance

Configuration Information

15

- There are two selections for 3000 Series transducers:

3000(-24V) Proximitor
Select this option when connecting a 3000 Series proximitor directly to a
3500 monitor. A default scale factor of 285 mV/mil will be selected. This
may be adjusted ±15 %. Note that the buffered transducers on the front
of the monitors and to the Data Manager are not compensated and
should be interpreted at 285 mV/mil.

3000(-18V) Proximitor
Select this option when connecting a 3000 Series proximitor directly to a
3500 monitor, but supplying proximitor power from an external 18 volt
source. A default scale factor of 200 mV/mil will be selected. This may
be adjusted ±15 %. Note that the buffered transducers on the front of the
monitors and to the Data Manager are not compensated and should be
interpreted at 200 mV/mil.

- Setpoints may only be set on proportional values which are enabled.
Monitors must be configured in channel pairs (for example, Channels 1 and 2

may be configured as Radial Vibration and Channels 3 and 4 may be
configured as Thrust Position).

- When a full-scale range is modified, the setpoints associated with this

proportional value should be readjusted.

- It is best to set the Scale Factor value and the Trip Multiply value before the

Zero Position value.

- 3000 (-18V), 3000 (-24V), and 3300 RAM Proximitors have limited linear

ranges. Therefore, you should use caution when selecting the Full-scale
range of the Direct, 1X Amplitude (Ampl), 2X Amplitude (Ampl), Not 1X
Amplitude (Ampl) and S

max

Amplitude (Ampl) PPLs. Full-scale value x Trip

Multiply should not exceed the linear range of the transducer.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
20
21
22
23
24
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: Radio Shack Страницы: 52

Бренд: QUAD Страницы: 16

Бренд: D+H Страницы: 14

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Faulhaber Страницы: 66

Бренд: u-blox Страницы: 28

Бренд: UNICORECOMM Страницы: 32

Бренд: UNICORECOMM Страницы: 7

Бренд: UNICORECOMM Страницы: 26

Бренд: UNICORECOMM Страницы: 25

Бренд: RadioMaster Страницы: 10

Бренд: Xblue Networks Страницы: 2

Бренд: Jetter Страницы: 24

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: SYR Страницы: 2

Бренд: DAQ Страницы: 63

Бренд: Danfoss Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды