Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 4

Страница: 4 / 226

iii

Additional Information

3500 Monitoring System Rack Installation and Maintenance Manual (129766-01)

•

general description of a standard system

•

general description of a Triple Modular redundant (TMR) system

•

instructions for installing the removing the module from a 3500 rack

•

drawings for all cables used in the 3500 Monitoring System

3500 Monitoring System Rack Configuration and Utilities Guide ( 129777-01)

•

guidelines for using the 3500 Rack Configuration software for setting the operating

parameters of the module

•

Guidelines for using the 3500 test utilities to verify that the input and output terminals on

the module are operating properly

3500 Monitoring system Computer Hardware and Software Manual (128158-01)

•

instructions for connecting the rack to 3500 host computer

•

procedures for verifying communication

•

procedures for installing software

•

guidelines for using Data Acquisition / DDE Server and Operator Display Software

•

procedures and diagrams for setting up network and remote communications

3500 Field Wiring Diagram Package (130432-01)

•

diagrams that show how to hook up a particular transducer

•

lists of recommended wiring

Notice:

This manual does not contain all the information required to operate and
maintain the Proximitor/Seismic Monitor. Refer to the Following manuals
for other required information.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PROXIMITOR 3500/42



































































































































































































































Результаты поиска

Содержание PROXIMITOR 3500/42

Отзывы:

Bently Nevada PROXIMITOR 3500/42, Руководство по эксплуатации и обслуживанию, Страница: 4 / 226

Результаты поиска

Содержание PROXIMITOR 3500/42

Отзывы: