Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 226

background image

3500/42 Operation and Maintenance

Maintenance

105

2X Amplitude (2X Ampl)

Note

The Keyphasor must be triggering and have a valid rpm value to check this
parameter.

1. Disconnect PWR, COM, and SIG field wiring from the channel terminals on

the I/O module.

2. Connect test equipment and run software as described in Section 5.1.5.1

(Test Equipment and Software Setup - Radial Vibration).

3. Set the Keyphasor multiplier/divider so that the multiply setting is one and the

divide setting is two. Adjust the function generator amplitude to produce a
reading that is within the 2X Ampl setpoint levels on the 2X Ampl bar graph
display of the Verification screen.

4. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

OK LED is on, the bar graph indicator for 2X Ampl is green, and the Current
Value field has no alarm indication.

5. Adjust the function generator amplitude such that the signal just exceeds the

2X Ampl Over Alert/Alarm 1 setpoint level. Wait 2 or 3 seconds after the
alarm time delay expires and verify that the bar graph indicator for 2X Ampl
changes color from green to yellow and that the Current Value Field indicates
an Alarm.

6. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for 2X Ampl remains yellow and that the Current Value
Field still indicates an Alarm.

7. Adjust the function generator amplitude such that the signal just exceeds the

2X Ampl Over Danger/Alarm 2 setpoint level. Wait for 2 or 3 seconds after
the alarm time delay expires and verify that the bar graph indicator for 2X
Ampl changes color from yellow to red and that the Current Value Field
indicates an Alarm.

8. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for 2X Ampl remains red and that the Current Value Field
still indicates an Alarm.

9. Adjust the function generator amplitude such that the signal reads below the

Over Alarm setpoint levels. If the nonlatching option is configured, observe
that the bar graph indicator for 2X Ampl changes color to green and that the
Current Value Box contains no indication of alarms. Press the RESET switch
on the Rack Interface Module (RIM) to reset latching alarms.

10. Repeat steps 3 through 9 to test the Under Alert/Alarm 1 and Under

Danger/Alarm 2 setpoints by adjusting the function generator amplitude to
exceed the Under Alarm setpoint levels.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
110
111
112
113
114
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 11

Бренд: Nauticam Страницы: 2

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 20

GEMINI C Series

Бренд: NAPCO Страницы: 24

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 140

Бренд: Absima Страницы: 5

Бренд: Apricus Страницы: 32

Бренд: Gardigo Страницы: 12

Бренд: DS Produkte Страницы: 4

Бренд: GEM Страницы: 56

Бренд: Lunt Solar Systems Страницы: 4

Бренд: Samson Страницы: 44

Бренд: Hansen Страницы: 12

Бренд: elsner elektronik Страницы: 148

Бренд: Gain Electronic Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды