Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 226

background image

3500/42 Operation and Maintenance

Maintenance

139

Peak to Peak

1. Disconnect PWR, COM, and SIG field wiring from the channel terminals on

the I/O module.

2. Connect test equipment and run software as described in Section 5.1.7.1

(Test Equipment and Software Setup - Eccentricity).

3. Adjust the function generator amplitude such that the signal level does not

exceed any setpoint value for the pp mil bar graph.

4. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

OK LED is on, the bar graph indicator for pp is green, and the Current Value
field has no alarm indication.

5. Adjust the function generator amplitude such that the signal just exceeds the

pp Over Alert/Alarm 1 setpoint level. Wait for 2 or 3 seconds after the alarm
time delay expires and verify that the bar graph indicator for pp changes color
from green to yellow and that the Current Value Field indicates an Alarm.

6. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for pp remains yellow and that the Current Value Field still
indicates an Alarm.

7. Adjust the function generator amplitude such that the signal just exceeds the

pp Over Danger/Alarm 2 setpoint level. Wait for 2 or 3 seconds after the
alarm time delay expires and verify that the bar graph indicator for pp
changes color from yellow to red and that the Current Value Field indicates
an Alarm.

8. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for pp remains red and the Current Value Field still
indicates an Alarm.

9. Adjust the function generator amplitude such that the signal reads below the

Over Alarm setpoint levels. If the nonlatching option is configured, observe
that the bar graph indicator for pp changes color to green and that the
Current Value Box contains no indication of alarms. Press the RESET switch
on the Rack Interface Module (RIM) to reset latching alarms.

10. If you can not verify any configured alarm, recheck the configured setpoints.

If the monitor still does not alarm properly or fails any other part of this test,
go to Section 5.1.11 (If a Channel Fails a Verification Test).

11. Disconnect the test equipment and reconnect the PWR, COM, and SIG field

wiring to the channel terminals on the I/O module. Verify that the OK LED
comes on and the OK relay energizes. Press the RESET switch on the Rack
Interface Module (RIM) to reset the OK LED.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
144
145
146
147
148
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: KAR-TECH Страницы: 28

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: IFM Страницы: 49

Бренд: K&G GROEP Страницы: 27

Бренд: CAME Страницы: 2

Бренд: CalAmp Страницы: 13

Бренд: Audioaccess Страницы: 2

Бренд: Aulisa Страницы: 32

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Roger Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды