Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 226

background image

3500/42 Operation and Maintenance

Maintenance

141

12. Disconnect the test equipment and reconnect the PWR, COM, and SIG field

wiring to the channel terminals on the I/O module. Verify that the OK LED
comes on and the OK relay energizes. Press the RESET switch on the Rack
Interface Module (RIM) to reset the OK LED.

13. Repeat steps 1 through 12 for all configured channels.

Direct

Note

The Keyphasor must be triggering and have a valid rpm value to check this
parameter.

1. Disconnect PWR, COM, and SIG field wiring from the channel terminals on

the I/O module.

2. Connect test equipment and run software as described in section 5.1.7.1

(Test Equipment and Software Setup - Eccentricity).

3. Adjust the power supply to produce a reading that is within the Direct setpoint

levels on the Direct bar graph display of the Verification screen.

4. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

OK LED is on, the bar graph indicator for Direct is green, and the Current
Value field has no alarm indication.

5. Adjust the power supply voltage such that the signal just exceeds the Direct

Over Alert/Alarm 1 setpoint level. Wait for 2 or 3 seconds after the alarm
time delay expires and verify that the bar graph indicator for Direct changes
color from green to yellow and that the Current Value Field indicates an
Alarm.

6. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for Direct remains yellow and that the Current Value Field
still indicates an Alarm.

7. Adjust the power supply such that the signal just exceeds the Direct Over

Danger/Alarm 2 setpoint level. Wait for 2 or 3 seconds after the alarm time
delay expires and verify that the bar graph indicator for Direct changes color
from yellow to red and that the Current Value Field indicates an Alarm.

8. Press the RESET switch on the Rack Interface Module (RIM). Verify that the

bar graph indicator for Direct remains red and that the Current Value Field
still indicates an Alarm.

9. Adjust the power supply voltage such that the signal reads below the Over

Alarm setpoint levels. If the nonlatching option is configured, observe that
the bar graph indicator for Direct changes color to green and that the Current
Value Box contains no indication of alarms. Press the RESET switch on the
Rack Interface Module (RIM) to reset latching alarms.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
146
147
148
149
150
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

SmartSwitch 6000

Бренд: Cabletron Systems Страницы: 76

Бренд: Jabra Страницы: 8

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: TUYA Страницы: 28

MultiLoad II EXL

Бренд: Toptech Страницы: 83

Бренд: AC Tech Страницы: 2

Бренд: V-TAC Страницы: 2

Бренд: Diamond Systems Страницы: 15

Бренд: Estun Страницы: 41

Elan SRB 201ZH X3

Бренд: schmersal Страницы: 6

Бренд: V2 Страницы: 180

Бренд: DNF Controls Страницы: 22

Бренд: Matelec Страницы: 2

DX99N9X1S2N0M2X0D2

Бренд: Banner Страницы: 13

Бренд: Burkert Страницы: 42

Бренд: Clemco Страницы: 14

Бренд: S&C Страницы: 12

Бренд: Parker Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды