Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 226

background image

3500/42 Operation and Maintenance

Configuration Information

33

3.1.4

Differential Expansion Channel Options

This section discusses the Configuration Considerations and the Rack
Configuration Software screens associated with the Differential Expansion
Channel.

3.1.4.1

Differential Expansion Channel Configuration Considerations

Consider the following items before configuring a Differential Expansion Channel:

- None of the differential expansion channel transducers are able to support

discrete Internal Barrier I/O modules.

- The "No Keyphasor" option is automatically selected for this channel type.

No Keyphasors are required.

- The Differential Expansion Direct full-scale range is dependent upon the

transducer type.

- The Zero Position voltage range is dependent upon the direct full-scale

range.

- Monitors must be configured in channel pairs (for example, Channels 1 and

2 may be configured as Differential Expansion and Channels 3 and 4 may
be configured as Thrust Position).

- When a full-scale range is modified, the setpoints associated with this

proportional value should be readjusted.

- The Latching OK Mode and the Timed OK Channel Defeat options are not

compatible.

- If a Non-Standard transducer is selected, the setpoint OK limits are set to

±1 volt from the Upper and Lower OK limits that are selected.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
38
39
40
41
42
...
»

Содержание PROXIMITOR 3500/42



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PROXIMITOR 3500/42

Бренд: Valve Concepts Страницы: 15

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: IBM Страницы: 20

Бренд: DAV TECH Страницы: 24

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

Бренд: Radionics Страницы: 14

Бренд: Yolink Страницы: 23

RSF-B mini Series

Бренд: Harmonic Drive Страницы: 32

Бренд: Pilz Страницы: 32

Бренд: Geberit Страницы: 12

multicomp F144-MS-1V1C1TI6RO-3

Бренд: KBR Страницы: 68

Бренд: OLYS Страницы: 4

The Boost Box WS 1107

Бренд: Watersports Innovations Страницы: 12

Бренд: Parker Страницы: 31

Бренд: Pixie Страницы: 21

Бренд: GIESSE Страницы: 136

BALBOA CS6000B Series

Бренд: HydroQuip Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды