Bently Nevada PROXIMITOR 3500/42 Скачать руководство пользователя страница 55

Страница: 55 / 226

Configuration Information

3500/42 Operation and Maintenance

may be configured as Acceleration and Channels 3 and 4 may be configured
as Radial Vibration).

- When a full-scale range is modified, the setpoints associated with this

proportional value should be readjusted.

- If a Non-Standard transducer is selected, the setpoint OK limits are set to ±1

volt from the Upper and Lower OK limits that are selected.

- When integration is selected, the available Direct Full-scale ranges will change

to reflect this.

- When band-pass filtering is selected, the high-pass and low-pass filters must be

set a minimum of two octaves apart.

- When two channels of acceleration are activated, the maximum channel

frequency supported is as shown:

Dual Channel

Configuration Settings**

Frequencies

Filtering

RMS

Integration

3 to 30 kHz

10 to 30 kHz

Yes

3 to 9115 Hz

Yes

10 to 9115 Hz

---

Yes

10 to 9115 Hz

Yes

** Three dashes represent both yes and no

- When a single channel of acceleration is activated, the maximum channel

frequency supported is as shown:

Single Channel

Configuration Settings**

Frequencies

Filtering

RMS

Integration

3 to 30 kHz

---

10 to 30 kHz

---

Yes

3 to 9115 Hz

---

Yes

** Three dashes represent both yes and no

- The Latching OK Mode and the Timed OK Channel Defeat options are not

compatible.

- Internal Barrier I/O Modules and External Barriers are not supported with high

frequency accelerometer transducers.

- Only 18 high frequency accelerometer transducers can be installed along with a

full rack of standard transducers. This is due to the fact that the rack can
only power 18 high frequency Accelerometer transducers.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PROXIMITOR 3500/42



































































































































































































































Результаты поиска

Содержание PROXIMITOR 3500/42

Отзывы:

Похожие инструкции для PROXIMITOR 3500/42

Бренды по названию

Популярные бренды

Bently Nevada PROXIMITOR 3500/42, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PROXIMITOR 3500/42

Отзывы:

Похожие инструкции для PROXIMITOR 3500/42

Бренды по названию

Популярные бренды