Xerox Legacy 4110 Page 469 User Manual Download

Page: 469 / 520

Xerox 4590/4110 Copier/Printer User Guide

11-91

11. Problem Solving

Hold the tabs of the booklet staple cartridge and then lift to
remove it.

Remove the jammed staples as shown in the illustration.

Holding the tabs of the booklet staple cartridge, return the
cartridge to the original position and gently push it until it

clicks.

Return the unit to its original position.

Close the Finisher right cover.

NOTE: A message will be displayed and the machine will not

operate if the right cover is even slightly open.

If the staples cannot be removed after carrying out the above

procedures, contact the Customer Support Center.

WARNING:

Be careful when

removing jammed

staples to avoid

hurting your fingers.

Summary of Contents for Legacy 4110









































































































































































































































































































































































































































































































































Search results

Summary of Contents for Legacy 4110

Reviews:

Related manuals for Legacy 4110

Brands by name

Popular brands

Xerox Legacy 4110, User Manual

Search results

Summary of Contents for Legacy 4110

Reviews:

Related manuals for Legacy 4110

Brands by name

Popular brands