Xerox Legacy 4110 Page 466 User Manual Download

Page: 466 / 520

Xerox 4590/4110 Copier/Printer User Guide

11-88

11. Problem Solving

Push it downward until click sound is heard.

Close the Finisher right cover.

NOTE: A message will be displayed and the machine will not

operate if the right cover is even slightly open.

If the staples cannot be removed after carrying out the above

procedures, contact the Customer Support Center.

D2 Finisher

The following section describes the remedy for staple jams in the

staple cartridge for the D2 Finisher.

Make sure that the machine has stopped and then open the
front cover on the light finisher.

Hold the R1 at the position shown in the diagram and lift it
slightly.

Pull out the staple cartridge.

Summary of Contents for Legacy 4110









































































































































































































































































































































































































































































































































Search results

Summary of Contents for Legacy 4110

Reviews:

Related manuals for Legacy 4110

Brands by name

Popular brands

Xerox Legacy 4110, User Manual

Search results

Summary of Contents for Legacy 4110

Reviews:

Related manuals for Legacy 4110

Brands by name

Popular brands