Viavi Xgig User Manual Download Page 166 | Manualshive

Page: 166 / 468

background image

Chapter 5, Template Browser/Template Editor

Template Editor

152

Xgig Analyzer User’s Guide

Figure 67: LAN Conversation Frame Editor, Dialog Box Example

Creating Custom Templates

Custom templates can be created adding conversations or port numbers. Enter values directly in
the correct offsets in the

Current Template Display

area.

You can edit the template by entering the station you want to select for in the

Add Conversation

to Template

area and pressing

OK

.

The small fields in the

Current Template Display

area define the data patterns that comprise a

template. The offset defines the position within the packet to start comparing the packet contents
with the values in the pattern. If a match occurs, then this portion of the condition is satisfied. The
pattern can be specified as a decimal, hexadecimal, or ASCII value.

Use the

Data Format

pull-down box on the right to specify if the pattern is in decimal,

hexadecimal, or ASCII. Use the

Offset Format

pull-down box to specify if the column and row

headers display in decimal or hexadecimal. Note that although you can display the data in different
formats, all formats use a byte boundary. Only byte quantities can be entered or displayed.

Any specific value you create for templates can have “don't care” values. For example, assume
you're only looking for

FFFF34

in the first three bytes of the MAC destination address. You could

specify the values in your template as

FFFF34XXXXXX

, where X indicates you don't care about

the values in the last three offsets. Note that for IPv4 addresses, which uses decimal values, using
X characters as partial sub-addresses will cause the complete sub-address to be treated as
wildcard. For example, 128.12X.2.2 will be treated as 128.XXX.2.2.

The hex or decimal patterns display in black or

magenta

. Displays in

magenta

within the

Current

Template Display

area mean that the display does not provide a complete view of the template.

The bytes are a macro pattern; for example, the logical OR of two different address patterns that
make up a two-way conversation. Note also that many ASCII patterns have no corresponding
display character.

«
...
164
165
166
167
168
...
»

Summary of Contents for Xgig





















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Xgig

Brand: Keithley Pages: 48

Brand: Yamaha Pages: 69

Brand: Daewoo Pages: 2

Brand: Gardner Bender Pages: 4

Brand: GAPS Pages: 36

Brand: yellow jacket Pages: 26

Brand: Yamaha Pages: 12

KEITHLEY 4200-CVU-PWR

Brand: Tektronix Pages: 6

Brand: Chauvin Arnoux Pages: 64

1101-3121-0049-800

Brand: S+S Regeltechnik Pages: 16

Brand: Isspro Pages: 2

MarMonix MSL-765

Brand: Farnell Pages: 15

Brand: Shimadzu Pages: 22

Brand: NARDA Pages: 14

Celviano AP-60R

Brand: Casio Pages: 44

BAE LX-XO-PL018-L S4 Series

Brand: Balluff Pages: 2

Mini-SuperGraph II

Brand: NOMIS Seismographs Pages: 44

Brand: Saab Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands