TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
Table 5-7.
318 VOLTAGE LEVELS FOR TESTING TTL
Power Supply
Pulse Generator
T/H Level
Expected
Output (V)
High (V)
Low (V)
V1(V)
V2(V)
V3(V)
Data
+1.65
+1.65
+1.15
-----
----
----
all Fs (hex)
+1.15
+1.65
+1.15
-----
----
----
all 0s
3.
Threshold Levels V1, V2, and V3
a.
Press the 318 THRESHOLD key.
b.
Refer to the values given in Table 5-8 in setting the power supply output level, the pulse generator output level, the
system threshold levels, and the INPUT Clock and Pod Threshold levels.
c.
Set the test equipment to the values necessary for Test 1 in Table 5-8 and press the DATA key.
d.
Press the START key and wait for the acquisition to be completed. Check to make sure that SLOW CLOCK is not
displayed on the screen.
e.
Check that data acquired are equal to the Expected Data given in Table 5-8.
f.
Set the 318 SRCH WORD to equal the Expected Data and then check that the quantity of SRCH words equals
256.
g.
Repeat Steps (a) to (f) for each test in Table 5-8.
h.
Disconnect the test setup.
Table 5-8.
318 VOLTAGE LEVELS FOR TESTING V1, V2, AND V3
Power
T/H
Test
Supply
Pulse Generator
T/H Level
Input
Expected
#
Output (V)
High (V)
Low (V)
V1 (V)
V2 (V)
V3 (V)
Clk A, B
Data
1
+5.25
+5.25
+4.75
+5.0
--
--
V1
all Fs
2
+4.75
+5.25
+4.75
+5.0
--
--
V1
all 0s
* 3
-4.75
-4.75
-5.25
-5.0
--
--
V1
all Fs
* 4
-5.25
-4.75
-5.25
-5.0
--
--
V1
all 0s
5
+5.25
+5.25
+4.75
--
+5.0
--
V2
all Fs
6
+4.75
+5.25
+4.75
--
+5.0
--
V2
all 0s
* 7
-4.75
-4.75
-5.25
--
-5.0
--
V2
all Fs
* 8
-5.25
-4.75
-5.25
--
-5.0
--
V2
all 0s
9
+5.00
+5.00
+4.50
+10.0
-0.5
+4.75
V3
all Fs
10
+4.50
+5.00
+4.50
+10.0
-0.5
+4.75
V3
all 0s
11
+0.25
+0.25
-0.25
0.0
0.0
0.00
V3
all 0s
* 12
-0.25
+0.25
-0.25
0.0
0.0
0.00
V3
all 0s
* 13
-4.50
-4.50
-5.00
+0.5
-10.0
-4-75
V3
all Fs
* 14
-5.00
-4.50
-5.00
+0.5
-10.0
-4.75
V3
all 0s
* Insure that the P6451 probe GND lead connected to the Power Supply Reference terminal is at the same potential as the
318 ground.
5-46
Summary of Contents for 318
